MPC Grid
by pzuzarte · pzuzarte/mpc-grid
A browser step sequencer that plays the MPC Sample over USB-MIDI and saves patterns into a copy of a project as MPC sequences. Needs Chrome or Edge; tested on firmware 1.3.0.12.
Images: from pzuzarte/mpc-grid
About
A step grid for the Akai MPC Sample that runs in your browser. Build patterns across all 8 pad banks, keep them in 16 sequence slots, play them on the MPC live over USB MIDI, and save them into a new copy of a project as MPC sequences.
It doesn't change the MPC's firmware or your original project files, and nothing is uploaded: your projects stay on your computer and your card.
Visits to the page are counted anonymously with GoatCounter, which uses no cookies and never receives your projects, samples or patterns.
Unofficial and not affiliated with or endorsed by Akai Professional or inMusic. Back up projects you care about. It has been tested with MPC Sample firmware 1.3.0.12.
Requires a current version of Google Chrome or Microsoft Edge. Other browsers don't offer the MIDI and folder access it needs.
The Help button in the page (or the ? key) explains setup, saving and every control.
MPC settings for live play
Connect the MPC by USB, press SHIFT + PAD 8 to open MIDI Configuration, then set:
- MIDI Port: USB
- MIDI In Channel: All
- Pad MIDI In: On
The MPC only makes sound if the loaded project has samples on the pads you use.
Patterns and sequences
- Slots 1-16 are sequences. Click an empty slot to start a pattern there.
- During playback, clicking a slot queues it for the end of the loop.
- Duplicate copies the pattern to the next empty slot.
- Bars sets the length of the current pattern. Shortening it removes notes past the new end, and Undo brings them back.
- Banks A-H are along the top of the grid, or press keys 1-8. A dot means the bank has notes in this pattern. "In use" shows pads with samples or notes.
- Steps sets the grid to 1/8, 1/16 or 1/32. Triplets (or the T key) switches to three steps in the space of two.
- Note repeat makes each new step play 2-8 evenly spaced hits, drawn as bars in the step. Alt-click an existing step to apply the current setting to it. These are saved as ordinary notes, so the MPC plays and shows them as separate hits.
- Each note's length is drawn as a bar. Drag from an empty step to draw a note of any length, or drag a note to change it, while a click removes it. This is useful for cutting loops at an exact point when the pad is set to Note On. It snaps to the grid, or hold Alt for single ticks. Clicking adds a step at the New note length, and Cmd-drag fills separate steps.
- Right-click a step (or Control-click on a Mac) to edit its velocity (1-127), length and timing in ticks, and probability. A dashed outline marks a step with less than 100% probability. The grid honours probability during live playback; whether the MPC does after saving hasn't been confirmed.
- Live volume and Live pan move the whole track on the MPC right away, using MIDI controllers 7 and 10. They aren't saved to the project. In tests, the MPC didn't respond live to filter, resonance or tuning over MIDI.
- The grid resizes to fit the window. If steps would be too small to click, it shows fewer bars at a time with arrows to move between them, and follows the playhead during playback.
Playing with S-1 Grid
With S-1 Grid open in the same browser, Play, Stop and tempo on either page control both. Untick Sync on either page to play them separately.
Working with projects
The MPC can't use MIDI and share its card at the same time:
- Put the MPC in SD Card Access mode, click Connect card, and choose the card. Chrome may ask you to allow access again on later visits.
- Pick a project under "On the card". It's copied into this browser's storage.
- Exit SD Card Access mode to play and edit it live.
- "Save to new project" writes a new project in this browser.
- Back in SD Card Access mode, "Copy to card" adds it to the card without overwriting anything. Eject the card before leaving that mode.
Projects must be saved to the card on the MPC for the grid to see them.
Sample names come from the saved project, because MIDI doesn't carry them. Load samples on the MPC, save the project to the card, and enter SD Card Access mode. If that project is open, its pad names update within a few seconds and unsaved patterns are kept.
Keep your work on the card. Unsaved patterns and projects in the grid live in this browser's storage for the site. Clearing your browsing data for the site erases them, and they won't appear in other browsers. Patterns made with "No project" can't be saved into a project.
Sending a pattern straight to the MPC (experimental)
"Send to MPC" plays the current pattern exactly once with MIDI start, clock and stop, so the MPC can record it without SD mode or a new project file. Arm SEQ RECORD on an empty sequence of the same length, with MIDI Sync In set to MIDI Clock, then click the button. This hasn't been confirmed on the hardware.
Known limits
- Live BPM is used for laptop playback and is not saved to the project.
- Sample assignment is edited on the MPC.
- Slots in use can be cleared but not removed from a project.
- A project whose format can't be reproduced exactly can be viewed but not saved, so nothing is ever silently altered.
Development
The site is plain HTML, CSS and JavaScript with nothing to build. Serve the folder from any local web server, because browsers only allow these features on secure pages and localhost. Tests need Node.js 21 or later:
npm test
Something wrong or missing on this page?
Opens GitHub's editor; your change becomes a pull request and you're credited as a contributor.